Are you sure your alternator is in prime condition? It’s hard to tell whether or not an alternator runs properly if you don’t know what to look for. The most straight forward way to test it is by using a voltmeter. If you’re well in sync with your automobile, there are a few other procedures you may try as well. Article writer: Matthew Wright. How Alternators Make ElectricityTechnically speaking, an alternator converts mechanical energy into electrical energy through a process known as alternating current. Alternators are electrical generators; what gives an engine its spark, the headlights their light, and the heater its power while the vehicles moving down the road. Although many people assume the battery powers all those things, the truth is that the battery only does one thing: start the engine or operate electronics when the ignition is off — for a limited time; once the engine fires, the alternator takes over and provides juice for everything. Read more from this great post Here. Your car’s battery light is a signal of when your car’s charging system is not working properly. This is due to a malfunctioning alternator, a battery running down, or a number of other things. It’s best to know what to do when your car’s battery light turns on: stay calm, look at all your vehicle gauges, and reduce power until you’re able to have an auto mechanic diagnostic for possible issues. By author Mike Allen. How to Properly Check the Juice in Your Car BatteryQ: My minivan has failed to start a couple of times recently, because of a low battery. It turns over, but won’t spin fast enough to catch. My mechanic says he tested the battery and it’s bad. But it’s only a year old. I checked the voltage at idle, and it’s 13.8 volts. All of the cells have plenty of water. I think it’s something else. A: There’s more to checking a battery than testing the voltage and looking inside for low water. For one thing, you need to check the voltage when the engine is off, not when the alternator is raising system voltage to its normal level. You can test for proper cranking voltage with a voltmeter while—you guessed it—cranking the engine. The several hundred amperes of current the starter motor draws should pull the battery voltage down to a normal 9 to 10 volts. Do this test: Disable the ignition or injection to prevent the engine from starting. Read the full article Here. Changing the busted alternator of a car is not a job for anyone and must be taken on by a professional. If you have a garage and some experience in fixing a car, this is a job you can do on your own, saving an expensive, and inconvenient, trip to the local mechanic. But if all else fails you really need a professionals touch to handle your automobile problems. Guanella Auto Body can help with all your automotive questions.
The post Car Alternator Basics appeared first on Exceeding expectations since 1978. via Blogger Car Alternator Basics
0 Comments
Car paint damage can be caused by a number of variables. Car accidents, kid accidents, poor parking practice, and other mishaps are all causes for a mark or two on your great paint job. While scratches do detract from the visual beauty of your car, paying a body shop for a new coat of paint or even a small touch-up can be an expensive task. By: John Decker How to Fix Car Bumper ScratchesFixing damaged plastic bumpers involves grinding, sanding, sculpting and painting. But it’s worth the effort for repairs that would cost less than your deductible. There ought a be a law: If there’s a post in a parking lot—any post—it should be high enough to see when you’re backing up. Unfortunately, the law we usually see applied is Murphy’s, and the resulting body-damage repairs will cost just a few dollars less than your insurance deductible. And that’s precisely the scenario we were faced with after trying to maneuver our trusty Honda Civic out of a tight space in a crowded mall parking lot. A lot of people would first try to do what you shouldn’t: Head to the local auto parts store for some el cheapo body filler and a can of matching spray paint. Surprise! The technology of auto body parts has changed—and you’ll need a completely different array of supplies to repair painted plastic parts than you would use to repair sheet-metal. Fortunately, there are a number of companies making repair and refinishing materials for plastic bumpers, as well as plastic fenders and door skins made from sheet molding compound. Read the full article here about Bumper Scratches. Do you have a bumper cover dent? A lot of auto shops can be very costly if you have them professionally done. Below are a number of methods in which anyone with a dent in their plastic bumper can do that will help repair or fix the dent out of the bumper cover. By: Author Matthew Wright. How to Install Front Bumper
You were minding your own business, driving down the road, when something jumped right in front of you and you smashed up the front of your truck. Maybe it didn’t happen exactly like that, but in any case you need to replace a bent and squished front bumper so your friends and loved ones will stop giving you that look all the time. You know the look, that “you are a screw-up because you’re driving a wrecked truck” look. In the case of this truck, however, something did jump right in front of it – a six-point buck chasing some you-know-what. At least his final thoughts were pleasant and hopeful. Read the full Post Source. Different vehicle types are best approached accordingly. If your car permits you to get below the car and heat the area of the dent, use that tip. If there is no squeeze room to get underneath the bumper or under the car, use the way that involves detaching the bumper cover from the vehicle. But if all else fails we at Guanella will offer you a permanent and professional, price competitive solution.
The post DIY Car Bumper Maintenance appeared first on Exceeding expectations since 1978. via Blogger DIY Car Bumper Maintenance Watch on YouTube here: Breadmakers: 5 Fast Facts via Douglas L. Slocum via Blogger Breadmakers: 5 Fast Facts
Do you have a bread machine, but no guidebook, for the reason that you obtained it at a yard sale, inherited it from a family member, or just misplaced the handbook? As an alternative of stowing it in a cupboard and adding to your "I'll use it in the future..." litter, get underway making your very own fresh, warm, delightful bread!
Take some time to examine it. There is a hinged cover, which can be raised and sealed; there may be a space in it, and perhaps a slight vent too. Next to the cover, you must see a control panel with a few buttons (and maybe a light or two if you have a fancy version). Inside the bread machine, there is a bread pan or bucket. There should be a handle on it, which is probably folded down so the lid will close. The bread bucket works as both the mixing bowl and the baking pan. In the center of the bread bucket will be a little bread paddle or kneading blade. It is responsible for kneading and mixing the dough. When the dough bakes, it bakes around the kneading blade. You must remove the blade from the bottom of the loaf after the bread is baked. Take the bread container out set it next to the basin. Get a gauging cup and fill it with H2O. Dispense the water into the bread bucket. Do it constantly, till the bucket is filled. Tally how many cups of water you are putting into the bucket, until you get a total. This part is vital, so portion carefully. When you choose a procedure, it is imperative that you equal it up to the size of the bread bucket you have. You would not want to make a 2 lb recipe in a 1 lb machine. It would cause in a big mess. See the rest of this article in its original source outlined below: http://ift.tt/2mDp7tR via Blogger Bread Machine Usage Facts Car owners often take their windshield for granted. As it seems to always be there when they are driving, and for the most part doesn’t cause any kind of trouble. It is, always, very integral that your windshield be in good condition. If it does need replacement, it has to be done right to ensure the drivers and passengers safety. Author Matthew Wright gives light on this important subject. Using String and Bubbles to Install a WindshieldThe “soapy string” trick — a classic to be sure. Modern windshields are held in place using very strong adhesive, but not too long ago they were installed using no adhesive and only the rubber held the whole thing in place. It was a good system, and ultimately easier to replace a damaged windshield. That was the up side. The down side to these old windshields was the rubber itself. When it was new, the rubber around a windshield kept a pretty tight grip on things. But as rubber ages, especially the old rubber formulas from back then, it shrinks and cracks. When windshield rubber shrank and cracked, water started to creep in. Even if this water didn’t drip onto your lap right away, it was oozing into parts of the car’s chassis that it shouldn’t have been, causing rust and, in some cases, electrical problems! Still, there are plenty of cars on the road today that have this type of windshield seal, and owners of these cars have no interest in updating to any type of glued in windshield. Read the full article Here. Windshield repair is a job that is particular with its own professional section. A DIY repair kit won’t be as good as a professional result, but it is a low budget procedure that’s good enough for minimal damage. This post will show you the ways to evaluate the risks, and how to fix your windshield if that is the best way forward. Thanks to author Mike Allen for his great post. How to Repair Your Cracked WindshieldIt’s a fine day. The sun is shining, traffic is moving along smartly and you haven’t a care in the world. Whack! Until now, that is. Now there’s a rosebud the size of a quarter smack in the windshield. What’s worse, it’s directly in y our line of sight. It must have been a hypervelocity rail-gun pellet fired at you by an Imperial Stormtrooper, because you didn’t see it coming or going. And as your heartbeat returns to normal, the awful truth soaks in: You’re going to have to have the windshield replaced. This means dealing with the glass shop, being without your car for a day or two, having a potentially leaky windshield and, worst of all, higher insurance premiums. Link to the full article Here. The final cost of repairing or a full replacement depends upon several factors, on your location, insurance, and type of Automobile Windshield. If you have any insurance at all, a visit to an auto glass repair shop like Guanella Auto Body could be a great move on both you and specially your car. The post Automobile Windshield Replacement appeared first on Exceeding expectations since 1978. via Blogger Automobile Windshield Replacement
A Standard Operating Procedure (SOP) is a manuscript comprising of a list of information on how to perform a chore. A current SOP may need to just be adapted and modernized, or you may be in a situation where you have to transcribe one from out of nothing. It sounds intimidating, but it's really just a list.
There is no correct or erroneous way to write an SOP. Nevertheless, your business perhaps has a number of SOPs you can discuss to for organizing strategies, outlining how they have a preference it done. What it simmers down to is this: Are you the best individual to be writing this? Do you know what the procedure involves? How it could go off beam? How to make it safe? If not, you may be well off offering it over to somebody else. A poorly-written -- or, what's more, inaccurate -- SOP will not only decrease income and lead to managerial disappointments, but it can also be hazardous and have hostile influences on anything from your team to the environment. In short, it's not a danger you should take. If you're writing or updating an SOP for a collection of persons that are acquainted with procedure, vocabulary, etc., and just would profit from a small and snippy SOP that's more like a list, you could just put pen to paper it in short-form.
Read more of the rest of the article from the article source:
via Blogger SOP DIY Writing Procedures Watch on YouTube here: 10 Monster Machines of ALL TIMES via Douglas L. Slocum via Blogger 10 Monster Machines of ALL TIMES
While you're in vocation school and up until your training period, work as an all-purpose workhand for a building company. Getting construction know-how early-on will help you get a good internship. Most all-purpose workhand spots do not need a high school diploma, so you can start at work while in school.
Hunt for jobs online or in your area news listing for tower crane worker careers. Direct your resume via email, and make sure to list your training programs and proper qualifications. A lot of construction businesses favor workers with more than a few years of know-how, so define any ventures you accomplished as an intern. Once you have years of familiarity working as a tower crane machinist, you can apply for higher-level professions. So long as you save your accreditation, you can work as a manager or administrator. If wanted, you could even take on a trainee of your own. Once you have gotten qualified, you will need to renew your permit every five years. Recertification for tower crane machinists is less rigorous: you will need to pass a test within an allotted time. Tower crane operatives who flop to renew their permit by its ending date will need to re-take the full physical, written, and hands-on assessments. A special mention to the article source below: http://ift.tt/2BFP0j3 via Blogger Expanding Your Crane Operating Experience Watch on YouTube here: LG Washing Machine Installation - DIY via Douglas L. Slocum via Blogger LG Washing Machine Installation - DIY |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
March 2018
Categories |